Search:

Type: Posts; User: stutzman

Page 1 of 13 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    2
    Views
    92

    Re: Steering Wheel Earnings

    I'm not familiar with the term 'earning', but I'm guessing you are referring to the decorative metal bands on the arms of the steering wheel. If that's the case, I just ran across this on ebay:...
  2. Replies
    7
    Views
    238

    Re: Early License Plate Light Bulb Connector

    So sorry, Jack.

    I meant to go rummaging through my part boxes when you first posted, but every time I got out to the garage I got distracted by other projects. Maybe I need fewer projects.
  3. Replies
    7
    Views
    238

    Re: Early License Plate Light Bulb Connector

    Don't send it back yet, Jack!

    Is this what you are looking for (shown here with the rest of the bulb holder)? If so, PM me you mailing address and I'll get it out in Monday's mail.

    Lucky you...
  4. Replies
    13
    Views
    505

    Re: Hunting for a 121.928.10 engine!!

    Well, OK, maybe pointing out the differences in the block is insufficient to differentiate between the 921, 928 an the 940.

    I'm pretty sure the 921 can be easily identified by the side plates. ...
  5. Replies
    6
    Views
    380

    Re: Very quiet Turn Indicator

    Yup, there's a large selection of such things from various vendors.

    The problem with choosing such things is that you will need to buy and reject a lot of them. Why? There is no way of knowing...
  6. Replies
    13
    Views
    505

    Re: Hunting for a 121.928.10 engine!!

    So my car is also victim of a number-less engine swap. I have long ago given up on authenticity, so the fact I've got a different engine doesn't bother me. Anyway, I've always thought that it was...
  7. Replies
    6
    Views
    380

    Re: Very quiet Turn Indicator

    Jeff, I'm interested in how your relay experiment turns out.

    I switched to LED turn signals some time ago and so had to swap out the flasher for a solid state one that would handle the LED bulbs. ...
  8. Re: Exhaust manifold, matt black or silver ceramic coating

    I sent my exhaust manifold to JetHot not quite two years ago and had them coat it with their "Extreme Polish" in "Satin Silver" color. It came back a bit more of a flat sliver than a satin, but I...
  9. Replies
    1
    Views
    265

    Engine supports

    I'm confused about rear engine supports.

    Job Number 24-1 in the Work shop manual supplement talks about two versions for the supports. The first version is 42 mm measured between the lower bolt...
  10. Replies
    3
    Views
    329

    Re: Windshield Washer Bladder/ Wiper Motor

    I've not found a good solution yet.

    Authentic classics sells https://www.authenticclassics.com/Rubber-Windshield-Washer-Pump-300SL-p/auth-007563.htm Maybe it might fit some other Mercedes, but it...
  11. Replies
    7
    Views
    792

    Re: Club starter wiring

    That was almost two years ago. I can't remember where I left my coffee cup ten minutes ago!

    I am pretty sure I did as suggested - removed the battery ground and the ground strap off the lower...
  12. Replies
    28
    Views
    1,664

    Re: Cold call from new member

    Ha! He called again!

    I was home and recognized the number. Answered with "Hey, Larry, I was wondering when you were going to call!"

    The discussion was pretty short. I told him he was...
  13. Replies
    4
    Views
    368

    Re: Is this car's owner a club member?

    I don't think its actually possible to put the wheel on up-side down.

    There's only one slot for the woodruff key to fit. I supposed it would be possible maybe to mis-install it at the universal...
  14. Replies
    28
    Views
    1,664

    Re: Cold call from new member

    Alrighty then. Malice it is.
  15. Replies
    28
    Views
    1,664

    Re: Cold call from new member

    I haven't talked to the guy. Could our membership officer (Bob?) confirm or deny if this guy is truly a new member?

    I'm likely to be a touch less rude when I do talk to him if I know he is a...
  16. Replies
    28
    Views
    1,664

    Re: Cold call from new member

    Well, add me to the list of folks old Larry has called.

    His message went to my answering machine and I've not called him back. Since he is obviously knowingly abusing our members list I'm tempted...
  17. Re: Rear engine mount bolt spinning freely - nut broke loose from rubber.

    So I've seen several references to the orientation of these grooves in the mounts, but nothing definitive that states what direction the grooves go. I have mine fore and aft. Could someone confirm...
  18. Replies
    5
    Views
    252

    Re: Removing Fuel Gauge - Advice please

    With those symptoms, I think I would be tempted to pull the fuel sender out of the gas tank and inspect it before I twisted myself up getting under the dash to get the gauge out.

    I found my sender...
  19. Replies
    1
    Views
    194

    Re: BBS style wheels

    They have been on E-bay for quite a while. Easily relisted again and again for over a year.

    I've considered picking them up for use as road-tripping wheels, but have decided against it every time...
  20. Thread: Gasket needs

    by stutzman
    Replies
    4
    Views
    403

    Re: Gasket needs

    I have a source here in the states has something of a cottage industry making custom gaskets for ancient aircraft engines out of modern materials (fiberglass re-enforced silicone and other things). ...
  21. Replies
    12
    Views
    923

    Re: Fuel pump primer

    My fuel pump used to give me a bit of resistance when I worked the lever. Not exactly consistently because (I think) it depended on where on the position the pump actuator was when the engine...
  22. Replies
    56
    Views
    4,047

    Re: Carburetor bolts and gasket

    Gerry sent me a set of his 3d printed prototypes. I tested them with the spare pair of mikunis I had on the self. I can confirm that they fit fine. The only pair of manifolds I have however are on...
  23. Replies
    56
    Views
    4,047

    Re: Carburetor bolts and gasket

    Hey Gerry, let me see how they fit on Mikunis. I'll PM you an address.
  24. Replies
    56
    Views
    4,047

    Re: Carburator bolts and gasket

    My speed reading gets me into trouble again. I missed the part where you said eariler "where the manifold attaches to the cylinder head".

    However, I was taking Francesco to mean the nuts and...
  25. Replies
    56
    Views
    4,047

    Re: Carburator bolts and gasket

    I've had my carbs off and on so many times I can't keep count. I am not currently using the air log, so that does make it easier. In order to make it a bit better, I've changed the bottom bolts to...
Results 1 to 25 of 306
Page 1 of 13 1 2 3 4